enEnglish

Low Solidifying Point Oleic Acid Manufacture Price

Low Solidifying Point Oleic Acid Manufacture Price
Product Introduction:
Description:Vegetable Base Appearance:Liquid Product Summery:FAC producted through hydrolysis, distillation and other processes based on soybean oil. Packing:20MT net/Flexitank Item Test Method Qualified Value Appearance Visual Conform Colour(Fe-Co) GB/T1722 5 Max Acid Value(mgKOH/g) GB/T9104.3 185-210 Iodine Value(gl2/100g) GB/T9104.1 144 Min Saponification Value(mgKOH/g) GB/T9104.2 186-211 Solidifying Point(℃) GB/T510 -12 Max Cloud Point(℃) ASTM D2500b -8 Max Saturated Fatty Acids(%) GB/T17376 2.5 Max Moisture(%) GB/T9104.6 0.3 Max Email:trade@dldpfattyacid.com WhatsApp:+8613342270663
Send Inquiry
Description
Technical Parameters

IV140 Distilled Soybean Fatty Acid: Composition, Reactivity, and Process Considerations for the Formulating Chemist

Most technical literature on fatty acid grades stops at the iodine value, which is a bit like describing a polymer by its molecular weight alone. The number is true, and it's insufficient. What follows is a more detailed treatment of IV140 distilled soybean fatty acid - what's actually in it, how the composition drives reactivity, and where the practical failure points are in downstream processing. This is written for people who run reactors, not people who read brochures.

2

Composition Beyond the Headline Number

Iodine value of 138–142 tells you total unsaturation but says nothing about its distribution. Our IV140 typically analyzes out (by FAME GC, AOCS Ce 1-62 or equivalent) in the following range: palmitic 4–7%, stearic 3–5%, oleic (C18:1) 20–26%, linoleic (C18:2) 48–54%, linolenic (C18:3) 6–9%. The linoleic fraction is the dominant contributor to the iodine value - each C18:2 molecule carries two double bonds and an iodine value contribution of roughly 181 on a pure basis - so the IV target is effectively a proxy for linoleic content plus the smaller linolenic contribution.

This matters because C18:2 and C18:3 behave differently in oxidative cure systems. Linolenic acid, with three non-conjugated double bonds, cyclizes and forms more crosslink sites per unit mass, but it also contributes disproportionately to yellowing on age and to after-tack in thick films. Formulators moving from a blended or lower-IV feedstock to a consistent IV140 occasionally observe slightly faster early cure with somewhat more yellowing in white or pastel systems. That's the linolenic fraction doing what linolenic does. If yellowing is a constraint in your system, ask for the full FAME distribution rather than the IV alone - two IV140 materials with identical iodine values can differ by two percentage points in linolenic content depending on the crude origin and cut strategy, and the film properties will reflect that difference.

The heavier cut that produces IV140 also carries elevated unsaponifiables relative to a mid-column cut - typically 0.5–1.2% in our material, mostly sterols and tocopherols carried over from the crude. Not usually process-relevant, but worth knowing if your downstream application involves vacuum distillation of derivatives, where unsaponifiables concentrate in still bottoms.

Esterification Kinetics: What Changes Going from IV120 to IV140

For alkyd production, the fatty acid itself doesn't participate in the iodine-value chemistry during esterification - the double bonds are spectators until the oxidative cure stage. What changes between grades is the chain-length distribution and, more subtly, the acid functionality per unit mass.

IV140's heavier cut skews marginally toward C18 and away from C16 relative to IV120, which lowers the average carboxyl equivalent weight slightly. Practically: for a given molar charge of polyol, you'll need roughly 1.5–2.5% more IV140 by mass to hit the same OH-equivalent balance, and the esterification tends to run marginally faster on an acid-number basis because the reaction is diffusion-friendly at comparable viscosities. In our customers' reported experience, the acid-number endpoint arrives five to ten minutes earlier at equivalent temperature and catalyst loading when switching from a mid-cut IV120 to IV140 - not enough to redesign a process around, but enough to notice if you're running batch-to-batch cycle-time comparisons.

Where the IV difference actually bites is downstream. Higher unsaturation means faster autoxidation during and after application: induction period shortens, oxygen uptake rates increase, and the drier demand profile shifts. The classic failure mode is over-drying - cobalt-catalyzed surface cure outpacing through-cure, giving a skinned film with a mobile sublayer. If your drier package was balanced for IV120, expect to rebalance: typically reduce primary drier (Co, Mn) loading by 10–20% and shift a portion into through-driers (Zr, or a calcium co-drier to complex and reduce adsorption losses into the pigment surface). This is standard reformulation territory, but it's the single most common source of complaints when customers switch grades without consulting their drier supplier, and it's worth flagging that the "fatty acid doesn't work" diagnosis is almost always a drier-package diagnosis in disguise.

Rosin Content and Its Process Implications

Fractionation economics being what they are, IV140 sits closer to the rosin boundary than IV120. Our specification holds rosin acids below 1.5% by GC, with typical production running under 1.0%. For alkyd and epoxy ester applications, this level is inert - rosin acids esterify along with the fatty acids and act as monofunctional chain terminators, marginally lowering molecular weight at high loading but doing nothing detectable below 2%.

Where rosin content becomes a real variable: maleated and fumarated resins, where rosin's conjugated double bond participates in the Diels-Alder adduction and shifts softening points; certain surfactant intermediates where rosin acids produce off-color sulfonates; and any application feeding into hydrogenation, where rosin's abietane skeleton hydrogenates at different rates and complicates catalyst deactivation modeling. If your process is sensitive to rosin at the hundreds-of-ppm level, specify a maximum in the purchase contract and request GC data per lot - we test routinely and can furnish it, but it won't appear on a standard COA unless asked for.

Color: What Gardner 4 Actually Represents

The Gardner color of fatty acid reflects a mixture of carotenoid residues, oxidation products (conjugated dienones and aldehydes), and trace polymerized material carried through the heavier cut. Bleaching during distillation removes the labile fraction, but the residual color in an IV140 at Gardner 3–3.5 is largely oxidation-derived and will deepen slowly on air exposure - an open drum at 40°C will darken measurably within a few weeks.

Two practical notes. First, color is not a stability indicator in the way formulators sometimes assume: a Gardner 3.5 material with low peroxide value will outperform a Gardner 2.5 material that's been sitting around oxidizing. Request peroxide value and anisidine if you're worried about oxidative history; we don't publish them on the standard COA but the lab runs them on request. Second, nitrogen-blanketed storage genuinely slows color development in partially consumed drums. If your drum turns over slowly, blanketing is cheaper than discarding darkened heel material.

Batch Variation: Sources and Bounds

Iodine value drift within a supplier's window comes from three sources: crude feedstock composition (seasonal and geographic), cut-point control precision, and column load. Our process holds the five-batch rolling mean within roughly ±1 of 140 under normal crude conditions; the individual batch spread of 138–142 reflects genuine feedstock variation, not control slop. During summer months, when southern-origin crude carries lighter fatty acid profiles, the cut must reach deeper into the heavy fraction to hold IV, which raises color and rosin marginally and costs 2–4 points of yield. This is why some suppliers' "summer IV140" behaves differently from their winter material, and why asking a supplier for per-month batch data over a full year is more informative than any single COA.

Acid value correlates inversely with IV on soybean material - the heavier cut's molecular weight distribution means IV140 typically runs 3–6 points lower in AV than IV120 from the same crude. If your stoichiometry assumes a fixed AV across grades, adjust; the saponification value tracks AV within a few points and doesn't carry independent information for well-refined material.

Handling and Practical Notes

Flash point above 300°C (PMCC) means no flammable-liquid classification for transport in most jurisdictions - relevant for site permitting, not for storage discipline. The material is skin-sensitizing under repeated contact like all long-chain fatty acids; standard chemical-handling PPE applies.

Autoxidation is the storage enemy, not hydrolysis. Moisture content below 0.3% and the material's inherent hydrophobicity make water uptake negligible in sealed drums, but headspace air in a half-empty drum will oxidize the surface layer over months. For inventory that turns slowly, buy drum quantities sized to consumption rather than price breaks, or specify nitrogen-blanketed ISO tanks if you're set up for bulk.

Crystallization below about 8–10°C is partial and reversible - the higher-melting C16:0 and C18:1-rich fractions solidify first. Gentle warming to 25–30°C rehomogenizes the material completely; aggressive local heating creates convection currents that can carry oxidized surface material into the bulk, so warm slowly and stir if the container allows.

Where IV140 Is the Wrong Answer

For completeness: applications needing low-temperature viscosity stability, long induction periods, or minimal yellowing (some clear coats, certain lubricant basestocks, pharma-adjacent excipients) are mismatched to IV140's reactivity profile. Similarly, if your formulation chemistry doesn't consume the additional unsaturation - metalworking fluids, some emulsifier systems - you're paying a 3–5% premium over IV120 for reactivity you'll then need to suppress with antioxidants. The grade earns its price in oxidative-cure and high-reactivity derivative chemistry, and is simply more expensive than necessary almost everywhere else.

 

item method SPEC. Result Individual
Judgment
Product form Visual liquid 25℃ Confirm pass
Colour (Fe-Co) GB/T1722 4max 3 pass
Acid value (mgKOH/g) GB/T 9104.3 195-209 197.4 pass
Iodine value (gI2/100g ) GB/T 9104.1 140min 143.7 pass
Saponification value (mgKOH/g) GB/T 9104.2 196-208 198.6 pass
Titre (℃) GB/T 9104.5 19max 20.3 pass
Moisture (%) GB/T 9104.6 0.3max 0.02 pass
C12+C14 (%) GB/T 9104.9 1max - pass
C16 (%) 8max 2.1 pass
C18 (%) 6max 5.1 pass
C18' (%) 20-35 26.7 pass
C18'' (%) 54-60 58.2 pass
C18''' (%) 8max 5.3 pass
Others (%) - 2.6 pass

 

 

Hot Tags: low solidifying point oleic acid manufacture price, China, manufacturers, price, quotation, free sample, filtration oleic acid low solidifying point, automotive industry oleic acid low solidifying point, biofuel oleic acid low solidifying point, low solidifying point oleic acid for odor control, oleic acid with low melting point, chemical stability oleic acid low solidifying point

Send Inquiry
Dalian Daping Oil Chemicals Co.,Ltd
contact us